试过三四个BT软件，都没有任何速度，是什么原因---(已解决)

代码： 全选

# Maximum and minimum number of peers to connect to per torrent.

#min_peers = 40

max_peers = 700

# Same as above but for seeding completed torrents (-1 = same as downloading)

#min_peers_seed = 10

max_peers_seed = 700

# Maximum number of simultanious uploads per torrent.

max_uploads = 70

# Global upload and download rate in KiB. "0" for unlimited.

download_rate = 2130

upload_rate = 30

# Default directory to save the downloaded torrents.

directory = /home/yourusername/.torrent

# Default session directory. Make sure you don't run multiple instance

# of rtorrent using the same session directory. Perhaps using a

# relative path?

session = /home/yourusername/.torrent/session

# Watch a directory for new torrents, and stop those that have been deleted.

#schedule = untied_directory,5,5,stop_untied=

schedule = watch_directory,5,5,load_start=/home/yourusername/.torrent/*.torrent

# Close torrents when diskspace is low.

#schedule = low_diskspace,5,60,close_low_diskspace=100M

# Stop torrents when reaching upload ratio in percent,

# when also reaching total upload in bytes, or when

# reaching final upload ratio in percent.

# example: stop at ratio 2.0 with at least 200 MB uploaded, or else ratio 20.0

#schedule = ratio,60,60,"stop_on_ratio=200,200M,2000"

# The ip address reported to the tracker.

#ip = 127.0.0.1

# The ip address the listening socket and outgoing connections is

# bound to.

#bind = 127.0.0.1

# Port range to use for listening.

port_range = 50000-50100

# Start opening ports at a random position within the port range.

#port_random = no

# Check hash for finished torrents. Might be usefull until the bug is

# fixed that causes lack of diskspace not to be properly reported.

check_hash = yes

# Set whetever the client should try to connect to UDP trackers.

#use_udp_trackers = yes

# Alternative calls to bind and ip that should handle dynamic ip's.

#schedule = ip_tick,0,1800,ip=rakshasa

#schedule = bind_tick,0,1800,bind=rakshasa

# Encryption options, set to none (default) or any combination of the following:

# allow_incoming, try_outgoing, require, require_RC4, enable_retry, #prefer_plaintext

#

# The example value allows incoming encrypted connections, starts unencrypted

# outgoing connections but retries with encryption if they fail, preferring

# plaintext to RC4 encryption after the encrypted handshake

#

encryption = allow_incoming,try_outgoing,enable_retry

# Enable DHT support for trackerless torrents or when all trackers are down.

# May be set to "disable" (completely disable DHT), "off" (do not start DHT),

# "auto" (start and stop DHT as needed), or "on" (start DHT immediately).

# The default is "off". For DHT to work, a session directory must be defined.

#

dht = auto

# UDP port to use for DHT.

#

# dht_port = 6881

# Enable peer exchange (for torrents not marked private)

#

peer_exchange = yes

#

# Do not modify the following parameters unless you know what you're doing.

#

# Hash read-ahead controls how many MB to request the kernel to read

# ahead. If the value is too low the disk may not be fully utilized,

# while if too high the kernel might not be able to keep the read

# pages in memory thus end up trashing.

#hash_read_ahead = 10

# Interval between attempts to check the hash, in milliseconds.

#hash_interval = 100

# Number of attempts to check the hash while using the mincore status,

# before forcing. Overworked systems might need lower values to get a

# decent hash checking rate.

#hash_max_tries = 10

encoding_list = UTF-8